INOX Products


INOX MX2

New life for mechanically sound older batteries and double life expectancy for new ones.

Product Images
Product Overview

For cars, motorcycles, boats, trucks, buses, aviation, farm & earth moving equipment, industrial, solar & stationary batteries.

Your battery needs Inox battery conditioner

Dissolves battery killing sulphation
Better & faster cold morning starts
Constant brighter lights
Rapid power recovery & recharge
Holds charge longer between uses
Increases battery efficiency up to 18%
Up to 2 – 3 times longer use
Gives new life to older batteries
Written
Manufacturer’s warranty

Up to 12 months additional full replacement warranty* on new lead acid batteries.

* Written warranty conditions apply.

The manufacturers of inox battery conditioner – candan industries pty ltd will give an additional battery warranty period equal the battery manufacturer’s warranty period or for a period of 12 months whichever is the lesser on all lead-acid batteries when

Inox battery conditioner is added to the battery from new.

Application & Uses

NEW LIFE FOR MECHANICALLY SOUND OLDER BATTERIES

AND DOUBLE LIFE EXPECTANCY FOR NEW ONES.

APPLICATIONS & USES

For all lead-acid batteries used in motor cars & cycles, boats & general marine, trucks, buses, farm & earthmoving machinery, stationary & generating plants, aviation, electric powered & driven machinery & equipment, isolated & independent transmitter & receiver installations, solar energy storage, emergency backup systems and all other industrial and commercial applications where lead-acid batteries are used.

Approximately 75% of lead-acid battery failures are caused by a build-up of sulphation on plates and separators. One treatment with INOX Battery Conditioner dissolves and helps prevent the recurrence of this battery killing sulphation, restores the active ingredients and allows the battery to operate at full capacity.

INOX Battery Conditioner will not harm batteries; it is purely an agent to help keep the electro-chemical process active longer in lead-acid batteries.

INOX Battery Conditioner can be added to a battery at any age, the older a battery is, the less effective INOX Battery Conditioner may be. If an older battery will not hold its charge properly, has recharging problems or is just generally slow, the addition of INOX Battery Conditioner in 95% of cases will give the battery additional new life for up to

2 – 3 years.

NB. INOX BATTERY CONDITIONER IS NOT A CURE ALL, IT WILL HAVE LITTLE

OR NO EFFECT ON MECHANICALLY UNSOUND BATTERIES.

BATTERY DOSAGE DIRECTIONS

Standard Batteries

Up to 100 AMP Hours

MOTORBIKES

CARS, 4 WD, ETC.

INOX BATTERY CONDITIONER IS AVAILABLE IN 4 SIZES:

92 ml (This size only, carries the Additional Full Replacement Warranty.)

1, 5 & 20 litre containers

ANSWERS TO COMMONLY ASKED QUESTIONS

ON INOX BATTERY CONDITIONER

What is INOX Battery Conditioner?

INOX Battery Conditioner is an electro-chemical catalyst that can be added to all

Lead-acid batteries to increase the performance and life of the battery.

What are the benefits of adding INOX Battery Conditioner to a lead-acid battery?

It helps stop lead sulphate build up on the plates, increases battery life by up to 2 to 3 times, increases battery efficiency by 18%, gives brighter lights, faster starts & recharge.

Will INOX Battery Conditioner work in older batteries?

Providing the older battery has only a sulphate problem and is mechanically sound, it should add another 1 to 2 years life to the battery. NB. There is about a 2 – 3% failure rate when adding INOX Battery Conditioner to older batteries. It is not recommended adding INOX Battery Conditioner to batteries that are more than 2 years old.

What is the INOX Battery Conditioners manufacturer’s warranty?

When INOX Battery Conditioner is added to a new battery in the first 2 weeks and the completed warranty form is sent to Candan Industries Pty Ltd, there will be an additional full replacement warranty on the battery equal to the battery manufacturer’s warranty to maximum of 12 months and will start the day the battery manufacturer’s warranty expires.

EG. Battery with 6 months battery manufacturer’s warranty gets an additional 6 months with the INOX Battery Conditioner (I B C) (making 12 warranties in total). 12 months

BMW plus 12 months I B C (24 months in total). 24 months BMW plus 12 months I B C (36 months in total).

Material Safety Data

   0339

 

 

INOX MX3

The only lubricant in the world with the special
Mx3 anti-corrosion, anti-moisture formula for
The twenty – first century (food grade approved ).


Product Images

Product Overview

Displaces – penetrates
lubricates – protects
INOX contains no silicon, acid, kerosene or dieselene.

INOX will not harm metal points or surfaces, plastics, paints, enamels, fibreglass, formica or neoprene seals.
INOX doesn’t dry out, gum up, become gooey or sticky or wash off with water !
INOX is non- conductive, non-static, non-toxic, non-corrosive and non-staining.

APPROVALS
FOOD GRADE
AUSTRALIA: Instrument of Approval is freely available on request.

NEW ZEALAND: NZFSA Approved C 12 (All animal product except dairy)

KOSHER CERTIFICATE K-ID FKD-HCTN Status Pavere

N.B. Copies of Food Grade Approvals & Kosher certificate can be downloaded from the INOX-mx3 MSDS page. They can also be faxed or posted directly to the recipient from Candan Industries Pty Ltd.
N. A. T. O. Defence Manufacturers Code No. Z5594/5 ( R. A. N. App.)

Application & Uses
Material Safety Data

INOX MX4 Lanox

Designed for heavy industrial, mining, farming, marine, earth moving and transport type use and where extreme climatic and high humidity conditions prevail.


Product Images

Product Overview

Lanolin is a natural wax found in animal wool especially the wool from sheep, commonly referred as ‘WOOL FAT’ or ‘WOOL GREASE’, it has wide spread uses, cosmetics, medical, soaps, etc. Down through the centuries the Egyptians, Romans, Vikings, sailors and soldiers alike all used lanolin as a very effective anti- corrosion and waterproofing agent for a variety of metals, materials, timbers, to protect sails, leather, cannons, etc. Although we make INOX, a quality anti-corrosion lubricant, there are areas where a lanolin based anti-corrosion lubricant like LANOX is sometimes better suited for the application at hand.

LANOX is a heavy duty anti-moisture, anti-corrosion lubricant made with a high grade lubricating oil and lanolin base with specialized chemical compounds.

LANOX contains no silicon, kerosene, acids or dieselene.

LANOX is harmless to metal points & surfaces, plastics, painted & enamel finishes, fibreglass, formica, rubber or neoprene seals.

LANOX doesn’t become sticky, gooey or gum up.

LANOX is non-conductive, non-static & non-corrosive.

LANOX has neutral properties, low flammability (NON-AEROSOL)

Application & Uses

Many people have asked me, “Why bring out another anti-corrosion lubricant when I had the best product of this type, INOX already on the market”. The answer is quite simple, sure INOX will cover most of the applications most of the times where an anti-corrosion lubricant is required, but there are times when a heavier, longer lasting anti-corrosion lubricant is needed to do the job. 4 years of research and testing went into LANOX before I brought it out on the market.

About 70% of the time LANOX and INOX can be used for the same application, INOX being more suitable for the lighter applications such as electrical, hobbies and the food and beverage processing industry ( FOOD GRADE APPROVED ) and LANOX suitable for the more extreme climatic and high humidity conditions. We have found that INOX may effect some of the more modern natural rubber products with continual long term use, LANOX doesn’t have this effect.
ANCHORS, CHAINS & SHACKLE BOLTS: For good protection against corrosion and helps

helps reduce fouling.

CONCRETE: Keeps shovels, trowels, floats & formwork clean and corrosion free between use – Stops mortar and concrete adhering to aluminium frames, window & door glass on construction and building work sites.

CONSTRUCTION & FABRICATION: Protects bare metal surfaces, frame work and welded joints in the open air from corrosion during construction before painting – Also good for the protection of all unpainted metal held in storage.

EARTH MOVING MACHINERY: Use as an anti-seize on track and blade bolts & nuts before screwing together – Protects all blades and bare metal surfaces between use.

FARM MACHINERY: Protects all painted and bare mental surfaces, sprockets, chains and cables from corrosion on all tractors, harvesters (grain, sugar, grape, etc), sowers, vegetable diggers and washers in use and in the off season.

IRRIGATION PLANT & PIPES: Keeps pump motors, cables, linkages, couplings and electricals clean and free from corrosion and lubricated while in use and when in storage.

JET SKIS & OUTBOARDS: Protects outboards, clamps, props and jet skis from salt water corrosion, will not harm or harden rubber fittings – Keeps control and steering cables and linkages in good working order, lubricated and corrosion free.

LIVESTOCK TRANSPORT: Spray on all livestock crates and gates (rail , road, etc) to protect from rust and chemical corrosion before transit or in storage. Lubricates and protects locks and hinges.

MINING: Protects all bare metal surfaces, pump motors (above and below ground), drag lines, winches and associated electricals from moisture and corrosion in humid and adverse weather conditions.

MOORINGS & SLIPS: Stops electrolysis – Keeps winches, cables, slip cradles and wheel bushes lubricated & corrosion free – protection for all electricals from moisture & corrosion.

PROTECTION: Protects all painted and bare metal surfaces in the open from moisture and corrosion – Protects all timber surfaces for water and dry rot ( may slightly darken bare timber but it will not harm it) – Waterproofs and protects leather harness’s, boots, etc. Protects Firearms, barrels, etc in long term storage, will not harm stocks or metal finishes.

TRAILERS: Boat, box & car trailers and horse floats, spray on chassis, springs, axles, hinges, couplings, winches, cables. light fittings and electricals for protection from sea air and salt water corrosion.

THREAD ANTI-SEIZE: Spray on all metal threads before joining, stops threads from corroding together, makes it easier to undo all joints, nuts, bolts and screws at a later date.
Lubricant for Boating and Fishing
Listen to comments from the leading boating and fishing professionals from Florida, USA

http://www.inoxlube.com/inox-products/lanox-mx4-heavy-duty-anti-corrosion-lanolin-grease/

ANSWERS TO COMMONLY ASKED QUESTIONS ON LANOX LUBRICANT.

WHAT IS LANOX.

LANOX is a Lanolin based anti-corrosion, anti-moisture lubricant.

What difference is there between LANOX and INOX.

LANOX has been designed for a more heavy duty application than the original INOX, it is not food grade approved like INOX because it contains Lanolin, solvents and oil, it has no adverse effect on rubber.

Can I use LANOX for any applications that I would normally use INOX.

In about 70% of instances LANOX & INOX will have the same results as both contain no silicon, acids, kerosene or dieselene. They are both top quality lubricants, cutting agents and anti-moisture, anti-corrosion sprays.

What are the areas that LANOX would be preferred over INOX.

For example LANOX is more suitable in certain marine applications such as Anchors, Chains & Shackle Bolts and in the protection of Outboard & Inboard Motors. INOX would be best used in areas such as Marine Radios, Sail Tracks (non-staining) and the protection of stainless & aluminium fittings ( good for polishing stainless steel, aluminium & fibreglass). For use in Firearms, LANOX is best used for long term storages purposes whereas INOX has better applications for the day to day cleaning and lubrication (anti-static) so it doesn’t attract dirt and helps clean barrel residues easier.

Does LANOX have applications in the Farming Industry.

Because of it’s Lanolin base it has good long term applications in areas such as cutter bars on headers, lawnmowers, linkages, etc to protect against rust and corrosion (spray onto moving parts to give protection during stand down periods). LANOX is a good anti-corrosion agent for bare metals in storage, stock crates or as a protectant after welding. LANOX is also a good long term lubricant for areas that traditionally receive little maintenance attention (ie. gate hinges, stationary motors, etc).

Does LANOX have applications for Earthmoving Equipment.
LANOX can be used as long term lubrication for linkages, cables couplings, etc and for corrosion protection in electrical systems as well as an anti-seize on track bolts and wheel studs.

Can LANOX be used as a cutting lubricant.
Yes, tests conducted prior to it’s release found that LANOX is an effective cutting, milling, tapping and thread cutting lubricant for a variety of metals.

It is especially effective on aluminium.

INOX® QUALITY PRODUCTS

“There is no substitute for Quality”

Material Safety Data

Technical Information

ASTM D4052 DENSITY @15.6°C .8461
DIELECTRIC 26
ASTM D93 FLASH POINT 179°C
ASTM D97 POUR POINT -26°C
ASTM D445 VISCOSITY (cSt, 40°C) 13
VISCOSITY (cSt, 100°C) 2.4
SOLUBILITY IN WATER NEGLIGIBLE

MSDS – Click to Download

MX 4 Lanox Grease

A quality food grade approved lanolin grease for protection against rust, corrosion & moisture in all industries when extreme climatic and high humidity conditions prevail.


Product Images

Product Overview

LANOX-mx4 Grease is a non-toxic, Food Grade Approved Lanolin grease.

It is made from a pure high technical grade anhydrous lanolin, food grade approved additives and anti-oxidants. It has been especially designed to remain pliable at very low temperatures with the right amount of gripping tackiness (non-fling) to hang on and still have flexibility for the user.

LANOX-mx4 Grease is waterproof, non-conductive and safe to use on all surfaces. It is highly suitable for anti-corrosion, rust proofing and anti-fouling coatings for all metals used in Automotive, Aviation, Commercial, Construction, Earthmoving, Farming, Industrial, Marine, Mining and Transport applications. Waterproofs and protects leather. Preserves timber from water, cracking and dry rot. (Do not use on green timber). Anti-seize for bolts, nuts and threaded rod. Stops electrolysis between dissimilar metals.

LANOX-mx4 Grease is Non-carcinogenic, bio-degradable, highly resistant to salt and acid corrosion, provides lasting protection.

LANOX-mx4 Grease is environmentally and user friendly.

LANOX-mx4 Grease looks like creamed honey and has no lanolin odour

FOOD GRADE APPROVED: Australia (Type ‘A’ ) Instrument of Approval is freely available on request from Candan Industries P/L.

KOSHER CERTIFICATE K-ID HTH-BBQK Status Pavere

Copies of the Food Grade Approval & Kosher Certificate can be down loaded from the download site at the bottom of the MSDS page.

Application & Uses

New Video: LANOX-mx4 Lanolin Grease

applied to the bottom of boats

Capt. Lee Shull of Fort Lauderdale, Florida using LANOX-mx4 grease for the long term protection from corrrosion and marine growth on the underwater running gear and fittings on a 100 ft. (30m) Sunseeker Luxury Cruiser.

http://www.inoxlube.com/inox-products/lanox-mx4-lanolin-grease/

ANCHORS, CHAINS & SHACKLE BOLTS: For good protection against corrosion and helps

helps reduce fouling. Anchor chains & shackles. Drum cables and net chains on trawlers and fishing boats.

CONCRETE: Keeps corrosion and moisture out of chains and open gears on mixers, agitators and helicopter finishers.

CONSTRUCTION & FABRICATION: Protects bare metal surfaces, frame work in the open air from corrosion during construction before painting – Also good for the protection of all unpainted metal held in storage.

EARTH MOVING MACHINERY: Use as an anti-seize on track and blade bolts & nuts before screwing together – Protects all blades and bare metal surfaces between use.

FARM MACHINERY: Protects all painted and bare mental surfaces, sprockets, chains & cables, PTO splines & couplings from corrosion on all tractors, harvesters (grain, sugar, grape, etc), sowers, vegetable diggers and washers in use and in the off season.

IRRIGATION PLANT & PIPES: Keeps pipe threads, chains, cables, linkages and couplings clean and free from corrosion and lubricated while in use and when in storage.

JET SKIS & OUTBOARDS: Protects outboards, clamps, props and jet skis from salt water corrosion, will not harm or harden rubber fittings – Keeps control & steering cables and linkages in good working order and corrosion free.

LIVESTOCK TRANSPORT: Apply to all livestock crates and gates (rail , road, etc) to protect from rust and chemical corrosion before transit or in storage.

MINING: Protects all bare metal surfaces, pump motors (above and below ground), drag lines, chains & winches from moisture & corrosion in adverse climatic conditions.

MOORINGS & SLIPS: Stops electrolysis – Keeps winches, cables, slip cradles and wheel bushes lubricated & corrosion free.

PROTECTION: Protects all painted and bare metal surfaces in the open from moisture and corrosion – Protects all timber surfaces for water and dry rot ( may slighty darken bare timber but it will not harm it) – Waterproofs and protects leather harness’s, boots, etc. Protects Firearms, barrels, etc in long term storage, will not harm stocks or metal finishes.

RUBBER & NEOPRENE: Protects and lubricates rubber and neoprene hoses, seals, bushes and O rings,

TRAILERS: Boat, box & car trailers and horsefloats, coat on chassis, springs, axles, hinges, couplings, winches and cables for protection from sea air and salt water corrosion.

THREAD ANTI-SEIZE: Apply to all metal threads before joining, stops threads from corroding together, makes it easier to undo all joints, nuts, bolts and screws at a later date.

Metal to metal soft seal gasket.

WIRE ROPE & CHAINS: Lubricates and protects chains and wire rope from corrosion.

CAUTION: LANOX-MX4 GREASE IS NOT RECOMMENDED FOR HIGH TEMPERATURE OR EXTREME PRESSURE BEARING APPLICATIONS.

INOX® QUALITY PRODUCTS

“There is no substitute for Quality”

Material Safety Uses

INOX MX5 Plus

premium quality – anti-corrosion – extreme

pressure liquid lubricant with ptfe


Product Images

Product Overview

EXTREME PRESSURE LUBRICATION

SUPERIOR PENETRATION

QUALITY ANTI-CORROSION PROTECTION

INOX mx5 Plus has been specially formulated by modifing the original INOX base formula together with the addition of a high grade friction modifier – Polytetrafluoroethylene.

INOX mx5 Plus has been designed for applications where a superior extreme pressure, anti-corrosion, anti-moisture liquid lubricant, a high grade penetrating oil or an industrial quality machine cutting lubricant is required (Safe to use in saw, lathe & milling reservoirs).

INOX mx5 Plus will not harm metal points or surfaces, fibreglass, formica, painted or enamel finishes, plastics or neoprene seals.

INOX mx5 Plus will not become tacky, alter surface tolerances, dry out

or wash off with water

INOX mx5 Plus is non-toxic, non-conductive, non-corrosive and non-staining.

Polytetrafluoroethylene (PTFE) is premium grade extreme pressure anti-friction medium which gives increased lubrication ability between the contact surfaces. This reduced friction environment also lowers operating temperatures.

Kosher Certificate K-ID DZH-PBQH Status Pavere

INOX mx5 Plus is Food Grade Approved (Type A) Australia

The Instrument of Approval is freely available on request and can be downloaded from the download site at the bottom of the INOX mx5 Plus MSDS page.

The Kosher Certificate can be downloaded from the same page.

Application & Uses

CAR & MOTORCYCLES: Starter motor, alternator, generator and solenoid shaft bushes – wiper motors and linkages – inner control cables – motorcycle clutch and accelerator cables (Ideal for classic/vintage heavy clutch cables)

COLD CLIMATE LUBRICANT: Ski bindings and snow board clips – snow mobile tracks, door hinges, locks and control cables – chair lift cables (prevents icing) – cold storage door locks and hinges, helps prevent switches, solenoid and valves icing up.

ELECTRICAL: all electric motor bushes – solenoid shaft assemblies – relay and switch gear pivot point bushes.

FARMING: Chain and sprocket drives – PTO splines and couplings – shearing hand pieces and equipment – control cables and linkages – winch cables – stock gate hinges and latches.

GENERAL: Pin bearings, bushes, screw & worm drives – slides & small linear bearings.

HOBBIES: Model train engine bushes and gears, rolling stock wheels and track switching points – all moving parts for model sailing and power boats, model cars, slot cars and tracks and model planes

INDUSTRIAL & MINING: Electric and pneumatic power tools – punching, stamping and folding equipment – conveyor and pneumatic systems lubricators – cutting, drilling and thread tapping – release agent (ie plastics, metal, etc) – factory roller doors – underground pump motor bushes.

MARINE & SHIPPING : Sail tracks – door hinges and locks – sliding hatches and pulleys – control cables – winch cables – high speed sail and line winders – sea container hinges and latches

RECREATIONAL USES: All firearms – roller blades and skate boards – gym and sporting equipment – mountain and racing pushbike chains, cables and wheel bearing hubs

TRUCK, BUS & TRAILER: Pneumatic door tracks and linkages – side curtain tracks alloy/stainless steel roller doors and tracks – air brake slack adjusters – inner control cables all starter motors, generators, alternators and wiper motors and all linkages, door hinges stock crate hinges and latches

AND

ANY OTHER APPLICATION WHERE AN EXTREME PRESSURE ANTI-CORROSION LIQUID LUBRICANT

IS REQUIRED

CAUTION: INOX MX5 PLUS MAY EFFECT SOME NATURAL RUBBER PRODUCTS

WITH CONTINUAL LONG TERM USE ( REFER TO LANOX )

INOX® QUALITY PRODUCTS

“There is no substitute for Quality”

Material Safety Data

Technical Information

ASTM 1298 DENSITY @15.6°C .865
ASTM D97 POUR POINT -13°C
ASTM D92 FIRE POINT 204°C
DIELECTRIC 33
ASTM D1744 KARL FISHER WATER 254.4 ppm
ASTM D445 VISCOSITY @ 40°C 10.86
VISCOSITY @ 100°C 2.74
ASTM D2509 Timken, OK load Kg 20
ASTM IP239 4 – Ball Weld Test – Kgf 275

MSDS - Click to Download


INOX MX6

EXTREME PRESSURE – HIGH TEMPERATURE ( NO MELT ) FOOD GRADE APPROVED MACHINERY GREASE with P T F E

INOX-mx6 is a fully synthetic Extreme Pressure grease formulated to give premium performance and food grade purity. This grease is composed entirely of ingredients which meet the requirements of section 178.3570 of the US FDA regulations and have been cleared for use within registered establishments by the US Department of Agriculture and will not deleteriously affect meat or meat products.


Product Images

Product Overview

INOX-MX6 IS FOOD GRADE APPROVED
Australia: Instrument of Approval is available on request.
New Zealand: NZFSA Approved C15 (All animal product except diary)
KOSHER CERTIFICATE K-ID FML-QVTB Status Pavere
N.B. Copies of Food Grade Approvals & the Kosher Certificate can be downloaded from the Material Safety Data Tab

Application & Uses

INOX-mx6 is a smooth light brown grease made with polyalphaolefins and a special bentone thickener. It contains additives to protect against corrosion and oxidation.

INOX-mx6 grease is recommended for all bearings and general lubrication and where processing temperatures go well below zero, especially in the refrigerated and frozen foods and beverage industries.

INOX-mx6 grease has a temperature range of -30 °C to an extremely high temperature

(HAS NO MELTING POINT).

P T F E – Polytetrafluoroethylene is a premium grade anti-friction medium which gives increased lubrication to bearings, bushes, shafts, gears, chains, splines, couplings, winches, cables, universals, CV & ball joints.

INOX-mx6 is highly suitable for all BEARINGS, BUSHES, CHAINS, HINGES, SPROCKETS, SLIDES, SPLINES & COUPLINGS, UNIVERSALS AND BALL JOINTS used in all Food processing Machinery, Beverage Filling Lines, Food Conveyor Lines, Food Packaging Equipment, Ovens, Freezers and Cold Rooms.

INOX-mx6 also has a wide spread application outside of the food and beverage industry.

Because of it’s Extreme Pressure lubricating ability and NO MELT temperature range, INOX-mx6 is highly suitable for all bearings, bushes, universals, etc used in Bitumen Transporting and Laying Machinery, Foundries, Paint Baking Ovens and all other high temperature applications. INOX-mx6 is also highly suitable for Truck, Trailer and all Farm Machinery wheel bearings, universals & ball joints, splines & couplings, Tierod Ends, Winches and Trailer Couplings.

NB. INOX-mx6 is a premium grade clay based Extreme Pressure grease. Using it with a non-clay based grease can seriously affect its performance. Before using INOX-mx6 grease, it is advisable to remove any other non-clay based greases by flushing or pushing out the old grease with INOX-mx6 in a grease gun.

INOX-mx6 EP Food Machinery Grease is available in 6 sizes:-

30 g Tube, 400 & 450 g Cartridges, 2.5 kg Tubs, 20 & 180 kg Drums

INOX® QUALITY PRODUCTS

“There is no substitute for Quality”

Material Safety Data

Technical Information

TYPICAL TESTS ASTM METHOD
NLGI 2
Appearance Smooth, light brown
Penetration at 25°C D.217 265 min – 295 max
Worked, 60 Strokes
Dropping Point, °C D.2265 Does not melt
Lower Operating Temperature °C - 30
Rust Prevention Rating D.1743 Pass
Timken, OK Load, Kg D.2509 23
4-Ball Weld, Kgf IP.239 500
Base Oil, cSt at 40°C D.445 46
Base Oil, cSt at 100°C D.445 7.8

MSDS - Click to Download


INOX MX7

PREMIUM GRADE ULTRA EXTREME PRESSURE MACHINERY ASSEMBLY AND BEARING LUBE – PIPE AND THREAD ANTI-SEIZE

Engine & Cylinder Head Assembly
Injection Mould Tool Lubricant
Mechanical & Electrical Equipment Assembly
Thread & Pipe Anti – Seize
Extreme Pressure Anti – Friction Applications
Contains Anti – Corrosion Additives


Product Images

Product Overview

INOX mx-7 is a specially formulated Extreme Pressure Lithium based grease containing a high percentage of Polytetrafluoroethylene (PTFE) designed for Ultra Extreme Pressure Lubrication and where tough Thread Anti-Seize applications are required.

INOX mx-7 provides high film strength, protects against start up damage in new and reconditioned machinery after long down periods before initial startup.

INOX mx-7 gives long term lubrication to parts and machinery that are difficult or impossible to lubricate after assembly.

INOX mx-7 allows for more even torque pressures and faster breakouts of joints, gaskets and threads

INOX mx-7 contains anti-corrosion additives.

Application & Uses

BEARINGS, SLIDES & BUSHES: All bearings and bushes – Slides, guides and bearing surfaces – Universals & CV joints – Assembly lubricant, where further lubrication is difficult or impossible after assembly

ENGINES & CYLINDER HEADS: Camshafts followers – Headstud shoulders – Valve stems and seals – Oil seals – gaskets surfaces – All crankshaft & camshaft bearing surfaces.

ELECTRICAL EQUIPMENT: Relay and switch gear hinge pins – Solenoid shafts Bushes & bearings for all motors, generators & alternators.

FARMING:
Chains & sprockets – PTO splines & couplings – Seals – Pumps – Windmill gears & shafts – shearing elbow & overhead gear – Travelling irrigators – Machinery assembly.

INDUSTRY:
All mechanical equipment and machine assembly – Hinges, slides, guides, splines, bushes and pins – cables & pulleys – Railway points & switch gear – Sewing machines – Open gears – Seals – Steering assemblies and cables – drive shafts.

MARINE: Cables & winches – Propeller shaft seals & stuffing boxes – Control and steering inner cables – Slip cradle wheel bearings and bushes.
THREADS & PIPES: Tapping & thread cutting lubricant – Seals pipe threads, greatly reduces corrosion freeze of threads.

TRANSPORT & AUTOMOTIVE: Gearbox spigot shaft splines, fly wheel bushes & bearings – Assembly of differentials and gearboxs – Door lock and wiper assemblies & linkages – Prime mover turntables – Hinge pins.

INOX® QUALITY PRODUCTS

“There is no substitute for Quality”

Material Safety Data

INOX MX8

A premium industrial grade – extreme pressure – high temperature – lithium complex and p.t.f.e. base grease


Product Images

Product Overview

The extreme pressure and anti-wear properties of INOX-mx8 grease gives long service life under high loading and shock loading conditions from very low to very high temperature environments. These special characters of shear stability, combined with the inclusion of effective rust, oxidation and corrosion inhibitors and tackiness adhesives, ensures this grease to be the preferred recommendation for sealed for life anti-friction bearings.

INOX-mx8 has the ability to prevent scuffing and reduce wear under high load and shock load conditions, together with its excellent high shear stability and high temperature operation, makes INOX-mx8 the preferred choice over other extreme pressure greases.

INOX-mx8 resists ‘SQUEEZE OUT’ from surfaces requiring lubrication under load conditions.

INOX-mx8 has excellent resistance to water and water wash out even at elevated temperatures. Effective lubrication is maintained and in these situations it also gives protection against rusting and corrosion.

INOX-mx8 will not thin out because it is shear resistant or thicken because it is resists oxidation.

P.T.F.E. – Polytetrafluoroethylene is a premium grade anti-friction medium which gives increased lubrication and reduces operating temperatures to bearings, bushes, shafts, gears, chains, splines, PTO’s, turntables, cables, universals, CV and ball joint

Application & Uses

AUTOMOTIVE: Wheel bearings – Ball joints – CV & universal joints – Tie rod ends – All control and gear change cables – All metal bushes and linkages – 4 WD winches – Trailer ball couplings.

AVIATION: Aircraft wheel bearings – All control cables and linkages – All bearings, bushes, control cables and linkages on ground support equipment and machinery.

BEARINGS: All sealed for life bearings – Open bearings and bushes – Worm and screw drives.

COMMERCIAL: All mower bearings, bushes and control cables – All wheel bearings, bushes, hoist chains, sprockets and control cables on Forklifts, Front End loaders and Pallet Trolley Jacks – Saw and log feed bed bearings in Saw Mills – Air conditioner bearings and bushes.

EARTHMOVING: All wheel bearings – Track sprockets and pins – PTO splines and couplings – Control cables. linkages, tie rod ends, chains and winches on Bobcats, Backhoes, Trenchers, Post Hole Diggers, Bull Dozers and Scrapers.

ELECTRICAL: All electrical motor, generator, Alternator bearings and bushes,

Solenoid shafts.

FARMING: All wheel bearings – PTO couplings and Splines – Chain drives and sprockets – Winches and cables – Wind mill bushes and shafts – Overhead and elbow gears in shearing sheds – Pump motors – Pins, linkage points, ball joints, universal joints, control cables on Tractors, Harvesters, All Farm Machinery and Equipment.

FISHING: All fishing reel bearings and bushes – Cable drum bearings, cables, gears and tackle blocks on Fishing Boats and Trawlers – Anchor winches and cables.

INDUSTRIAL: Fan motor bearings in cold rooms and freezers – Conveyor belt bearings All machinery.

MARINE: Boat trailer wheel bearings – Trailer ball couplings – Deck and anchor winches Steering control cables – All electric motor bearings, bendex assemblies and solenoid shafts – Stuffing box bushes.

MINING: All bearings, chain drives, PTO splines and couplings, ball joints, universal joints, control cables, tie rod ends, turntables, pins, bushes and hinges used below and above ground – All electric motors and solenoid shafts, pumps, Draglines, Dump Trucks, Grading and Sorting Machinery, conveyors and all other Mining Machinery and Equipment.

SHIPPING, WHARVES & SLIPS: Hinge pins on container doors – All bearings, bushes, pins, linkages, ball, universal & CV joints, control cables, chains used in winches, Hoists, Loading Equipment, Cranes, Forklifts, Container Handlers and Wharf Machinery Bearings, bushes and cables used in Winches and Boat Cradle Wheels & Tracks on slips.

TRANSPORT: Wheel bearings – Ball joints – King pins – Universal joints – Turn tables Spring shackles – Air brake slack adjusters – Trailer couplings – Tie rod ends – Idler arm bushes – Control cables and linkages – All electric motor and air starter motor bearings.

INOX-mx8 EP Grease is available in 6 sizes:-

300g Aerosol Spray Grease – 450 g Cartridges – 500 g & 2.5 kg Tubs – 20 kg & 180 kg Drums

INOX® QUALITY PRODUCTS

“There is no substitute for Quality”

Material Safety Data

Technical Information

TEST ASTM METHOD
NLGI 2
Soap Type Lithium Complex
Colour Red
Texture Smooth & Tacky
Penetration at 25°C
Worked, 60 Strokes D.217 280 min. – 305 max
Dropping Point, °C D.2265 260+
Lower Operating Temperature °C - 20
Leakage, Wheel Bearing 65g
Packed, 163°C, g D.1263 1.5
Water Washout at 80°C, % D.1264 3.5
Oil Separation
24 hours at 25°C kPa D.1742 2
Oxidation Stability -
Pressure Drop at 100 Hour, kPa D.3336 15
Pressure Drop at 500 Hour, kPa D.3336 70
Lubrication Life, Bearing No. 204
10000 rpm, 163°C, Hours D.3336 125
Rust Prevention Rating D.1743 Pass
Timken, OK Load, Kg D.2509 26
4-Ball Weld, Kgf IP.239 575
4-Ball Wear Scar, mm D.2266 0.48
Base Oil, cSt at 40°C D.445 190

MSDS - Click to Download


INOX MX9

INOX-mx9 No Chukka Chain Lube is a superior grade, high speed, extreme pressure chain lube formulated with special tackifiers, coagulants, anti-corrosion and water proofing compounds to make it stay on the chain, hence the name ‘No Chukka Chain Lube’


Product Images

Product Overview

INOX-mx9 No Chukka Chain Lube is a superior grade, high speed, extreme pressure chain lube formulated with special tackifiers, coagulants, anti-corrosion and water proofing compounds to make it stay on the chain, hence the name ‘No Chukka Chain Lube’.

INOX-mx9 No Chukka Chain Lube contains the extreme pressure friction modifier PTFE (polytetrafluoroethylene) which gives increased lubrication, reducing wear and also helps in reducing operating temperatures.

INOX-mx9 No Chukka Chain Lube is highly resistant to salt, chemicals, water wash out and drying.

Because of its’ heavy duty, highly tackified mass and extreme pressure lubricating ability, INOX-mx9 No Chukka Chain lube can be used in other lubrication applications, such as small ball and pin bearings, bearing slides, metal bushes, winch cables, etc.

DIRECTIONS FOR USE

It is recommended to clean the chain first by spraying it with INOX-mx11 Chain & Brake Clean. This will clean the chain and leave it dry in a few minutes with no residue. Next spray INOX-9 No Chukka Chain Lube directly onto the chain. NB. Using the extension tube attached to the spray button will give the best results for accuracy and concentration and reduces the problems with over spray. Allow a few minutes (3 to 10 mins depending on the ambient temperature) for chain lube to penetrate the chain linkages and for the solvent carrier and propellant gas to evaporate.

INOX-mx9 No Chukka Chain Lube

will not harm motorcycle chain ‘O’ rings

INOX-mx9 No Chukka Chain Lube

is available in 150 and 300 gram aerosol cans.

INOX® QUALITY PRODUCTS

“There is no substitute for Quality”.

Application & Uses

Motorcycle, bicycle and go-kart chains

• Forklift hoist chains

• Vehicle hoists and endless chain hoists

• Chain and sprocket drives for all farm and mining machinery,

industrial and commercial equipment

• P T O’s

• Winch cables

• Metal bushes

• Bearing slides, small pin, ball and roller bearings

MOTORCYCLES: To get the best life out of motorcycle chains, it is recommended to clean the chain after every third or fourth application of INOX-mx9 No Chukka Chain Lube.

For the best results, it is recommended to apply to a warm chain.

INOX-mx9 No Chukka Chain Lube

will not harm motorcycle chain ‘O’ rings

INOX® QUALITY PRODUCTS

“There is no substitute for Quality”

Material Safety Data

INOX MX11

READILY REMOVES OIL, GREASE AND BRAKE FLUID FROM CHAINS, BRAKE & CLUTCH ASSEMBLIES AND MACHINERY PARTS BEFORE OR AFTER DISASSEMBLY


Product Images

Product Overview

INOX-mx11 CHAIN & BRAKE CLEAN is a fast acting degreaser for removing brake fluid, oil, grease or oil/grease dirt contaminants from chains and brake assemblies (including linings and pads) before or after disassembly, leaving them bone dry and squeaky clean in a matter of minutes with no residue. In instances where the oil/grease and dirt is caked on, a second application maybe required and at the same time it is advisable to use a firm non-metallic bristled cleaning brush to help loosen any caked on contaminant.

INOX-mx11 Chain & Brake Clean readily dissolves oil, grease and grime and can be used as a degreaser for car, motorbike, truck, boat, industrial, mining, farming equipment parts, gears, cables, engines or on any equipment where there is contamination from any oil, grease or oil/grease dirt mixtures.
INOX-mx11 Chain & Brake Clean is a solvent based cleaner that dries in minutes and leaves no residue.

CAUTION: Avoid direct contact with rubber and perspex and prolonged contact with neoprene and plastics.

Use in a well ventilated area.

INOX-mx11 Chain & Brake Clean
is available 500 gram aerosol cans and 20 litre drums.
INOX® QUALITY PRODUCTS

“There is no substitute for Quality”

Application & Uses

INOX-mx11 Chain & Brake Clean readily dissolves brake fluid, oil, grease and grime and can be used as a degreaser for the following.

• Disc Brake assemblies, disc brake pads – before and after disassembly.

• Brake shoes and backing plates, master and slave cyclinders.

• Brake cables, inner control and steering cables.

• Clutch plates and pressure plate assemblies

• Petrol and diesel engines and their component parts.

• Motorbike, bicycle and go-kart chains and sprockets.

• Endless, machinery hoist and vehicle hoist chains.

• Forklift hoist and industrial machinery chains and cables.

• Winch cables and chains

• PTO’s, farm and mining machinery chain and sprocket drives.

• All machinery and equipment component parts

MOTORCYCLES: INOX-mx11 Chain & Brake Clean is ideal for cleaning gritty oil and dirt residue off bike chains and sprockets, leaving them clean and dry and ready for lubrication. INOX-mx9 No Chukka Chain Lube with PTFE is recommended for motorbike chains & sprockets.

INOX-mx9 No Chukka Chain Lube with PTFE can be used quite effectivly to lubricate most chains and cables, but for heavier applications, INOX-mx8 Spray Grease is more suited for these types of applications.

(INOX-mx8 Spray Grease is a Lithium complex and PTFE based exterme pressure, high temperature grease that is highly resistant to water wash-out, salt and chemicals).

CAUTION: When using INOX-mx11 Chain & Brake Clean avoid direct contact with rubber and perspex and prolonged contact with neoprene and plastics. Use in a well ventilated area.

INOX® QUALITY PRODUCTS

“There is no substitute for Quality”

Material Safety Data

INOX MX12

A fast drying – resin bonded, water proof & Abrasion resistant polytetrafluoroethylene dry film lubricant coating for timber, glass, metal, plastic, rubber and most other surfaces


Product Images

Product Overview

INOX-mx12 PTFE SUPA GLIDE is a fast drying, resin bonded polytetrafluoroethylene dry film lubricant for the coating of timber, metal, plastic, rubber, glass and most other surfaces.

It is designed for low-friction, light load repetitive stresses that allows moving parts to wear longer, work harder and require less maintenance.

Has applications where other conventional sintered PTFE coatings cannot be considered.

• Excellent lubrication qualities

• Good surface adhesion

• Hard abrasion-resistant surface

• Clean and easy to apply

• Thin film

• Longer wear life than pure PTFE coatings

• Cures at room temperature

• Inhibits corrosion

• Doesn’t wash off with water

• Resists contamination from dirt and dust

• Life-long lubrication in many applications

Application & Uses

SURFACE PREPARATIONION

Before applying INOX-mx12 PTFE SUPA GLIDE, the surfaces sould be clean, dry and free of contaminants such as oil, grease, dust or powder. A light sanding with 120 grit sandpaper or emery cloth followed by a solvent wipe and air dry is usually sufficent. More critical applications requiring optimum adhesion, the following pretreatments are suggested.

WOOD

STEEL

STAINLESS STEEL

ALUMINIUM

COPPER ALLOYS

RUBBER, PLASTIC

& GLASS

Sand lightly and wipe clean

Degrease or sandblast

Degrease or sandblast

Degrease, sandblast or anodize

Degrease, sandblast and/or acid etch

Clean with a solvent that will not effect the substrate

INOX-mx11 Chain & Brake Clean is a good degreaser for cleaning all metals, glass and some plastics. It dries very quickly and leaves no residue. NB. DO NOT USE TO CLEAN RUBBER PRODUCTS.

INOX-mx12 PTFE Supa Glide is recommended for :-

• Sliding door, window and curtain tracks

• Sailtracks

• Garage/factory roller door tracks

• Truck/trailer side curtain tracks

• Moving furniture parts

• Piano action parts

• Flexible inner cables

• Solenoid plungers

• PTO couplings

• Pulleys & open gears

• Winches and cables

• Metal, plastic and neoprene bushes

• Saws & guillotines

• Metal punching/stamping machines

• Looms

• Work surfaces for work tables/sewing machines

• And any other sliding or turning surfaces that require

a high grade, hard wearing dry lubricant.

CURING TIME

INOX-mx12 PTFE SUPA GLIDE will cure at room temperature.

Coatings are touch dry in about 5 minutes and dry enough to handle in 20 to 30 minutes depending on the film thickness.

Optimum hardness for the best lubrication operation is 2 hours. It is strongly advised to allow 2 hours from application to use for the best long term results.

High humidity may increase opacity or blush and exposure to strong sunlight may cause darkening, but these will not effect the coating performance.

IMPORTANT NOTICE: INOX-mx12 APPLICATIONS MUST BE FULLY CURED (APPROX 2 HRS) BEFORE THEY CAN BE USED. IF IS NOT CURED PROPERLY THE COATING MAY RUB OFF OR STICK TO ANOTHER SURFACE PREMATURELY

INOX® QUALITY PRODUCTS

“There is no substitute for Quality”

Material Safety Data
© Copyright - INOXNZ - Site by Enervate